Proxim ORiNOCO AP-8000 Guía de usuario Pagina 129
- Pagina / 169
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Using CLI to Manage the Access Point AP-8000 User Guide
Configuring the Device Using CLI Commands
129
protocol-number: 08:88
filter-status: block
row-status: notInService
}
index 19 {
protocol-name: EAPOL ether type
protocol-number: 88:8e
filter-status: block
row-status: notInService
}
Static MAC Table Configuration
The Static MAC Address filter optimizes the performance of a wireless (and wired) network. When this feature is properly
configured, the AP can block traffic between wired devices and wireless devices based on MAC address. Perform the
following commands to configure Static MAC .
(config)# dev-configure
(config-dev<config>)# filtering
(config-dev<config>-filter)# static-table
(config-dev<config>-filter-static<mac>)# index 1 ?
Possible completions:
<[Enter]> Execute this command
filter-comment Static Mac Address Comment
row-status Filter Table Row Status
wired-mac-address Wired Mac Address Filter
wired-mac-mask Wired Mac Mask
wireless-mac-address Wireless Mac Address
wireless-mac-mask Wireless Mac Mask
(config-dev<config>-filter-static<mac>)# index 0 row-status 4
(config-dev<config>-filter-static<mac>)# index 0 wired-mac-address 00:a6:33:44:23:34
(config-dev<config>-filter-static<mac>)# index 0 wired-mac-mask FF:FF:FF:FF:FF:FF
(config-dev<config>-filter-static<mac>)# index 0 wireless-mac-address 00:c3:d3:23:44:23
(config-dev<config>-filter-static<mac>)# index 0 wireless-mac-mask FF:FF:FF:FF:FF:FF
(config-dev<config>-filter-static<mac>)# index 0 filter-comment test
(config-dev<config>-filter-static<mac>)# index 0 row-status 4
#show
Device-Name# show configure filtering static-mac-addr-filter
// RUNNING-CONFIGURATION //
// Static MAC Address Filter Table //
index 1 {
wired-mac-address 00:a6:33:44:23:34
wired-mac-mask FF:FF:FF:FF:FF:FF
wireless-mac-address 00:c3:d3:23:44:23
wireless-mac-mask:FF:FF:FF:FF:FF:FF
filter-comment:test
row-status:active
}
TCP/UDP Port Filter Configuration
Port-based filtering enables you to control wireless user access to network services by selectively blocking TCP/UDP
protocols through the AP. Perform the following commands to configure TCP/UDP Filter
(config)# dev-configure
(config-dev<config>)# filtering
- ORiNOCO AP-8000 1
- Copyright 2
- Trademarks 2
- GPL License Note 2
- OpenSSL License Note 2
- Introduction 8
- Quality of Service (QoS) 9
- Software Upgrade 9
- Hardware Overview 10
- Prerequisites 12
- System Requirements 13
- Product Package 13
- Optional Accessories 14
- Hardware Installation 14
- Using a Console Port 15
- Install the Antenna 15
- Mount the Unit 15
- Power on the Unit 16
- Initialization 18
- Installing the Software 22
- Managing the Access Point 27
- SNMP Management 28
- SSH (Secure Shell) Management 28
- HyperTerminal 28
- ProximVision ES 29
- Password Management 31
- 7. Click COMMIT 33
- Access Point Features 34
- Ethernet 36
- Security 36
- IP Configuration 43
- TPID Priority CFI VID 45
- Managing the Device 48
- Upgrading the Firmware 49
- Monitoring the Device 51
- Interface Statistics 52
- Network Layer 54
- Web Interface Overview 56
- Error Message 56
- Configuring the Device 57
- Wireless 58
- Filtering 73
- Management Access Control 88
- System Log 91
- Event Log 93
- Pre-requisites 102
- Viewing the MIB Objects 102
- Configuring the MIB Objects 103
- General Notes on CLI 105
- Navigation and Special Keys 106
- Messages 106
- List Commands 107
- Command Line Completion 107
- Rules for Table Objects 107
- User Execution Mode 108
- Privileged Mode 108
- Log into the AP using Telnet 109
- Device Configuration 111
- // RUNNING-CONFIGURATION // 127
- TFTP Configuration 133
- Telnet configuration 133
- HTTP Configuration 133
- Country Code Configuration 136
- Inventory management 136
- Event Log Configuration 137
- SNTP Configuration 138
- // INTERFACE STATISTICS // 139
- Display the ICMP Statistics 141
- Display the IPARP Statistics 141
- Troubleshooting 144
- Symptoms and Solutions 145
- Client Connection Problems 147
- VLAN Operation Issues 147
- Gigabit Ethernet PoE 148
- Recovery Procedures 149
- Related Applications 153
- ASCII Character Chart 154
- Bootloader CLI 155
- Specifications 157
- Advanced Bridging Functions 158
- Security Features 158
- Hardware Specifications 159
- Available Channels 160
- Support Options 166
- Statement of Warranty 168
- Other Information 169
Relacionado con productos y manuales para Redes Proxim ORiNOCO AP-8000
Redes Proxim RangeLAN2 7921 Guía de usuario
(103 paginas)
(103 paginas)
Redes Proxim ORiNOCO AP-2500 Guía de usuario
(251 paginas)
(251 paginas)
Redes Proxim AP-2000 Guía de usuario
(244 paginas)
(244 paginas)
Redes Proxim RangeLAN2 7500 Manual de usuario
(141 paginas)
(141 paginas)
Redes Proxim 7910 Guía de usuario
(127 paginas)
(127 paginas)
Redes Proxim RangeLAN2 7921 Especificaciones
(76 paginas)
(76 paginas)
Redes Proxim RANGELAN2 7510 Guía de usuario
(84 paginas)
(84 paginas)
(9 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales