Proxim ORiNOCO AP-700 Manual de usuario Pagina 129
- Pagina / 242
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Troubleshooting the AP-700 AP-700 User Guide
Recovery Procedures
129
7. Enter only the following statements:
[Device name]>
set ipaddrtype static
[Device name]>
set ipaddr <Access Point IP Address>
[Device name]>
set ipsubmask <IP Mask>
[Device name]>
set tftpipaddr <TFTP Server IP Address>
[Device name]> set tftpfilename <AP Image File Name, including file extension>
[Device name]> set ipgw <Gateway IP Address>
[Device name]>
show ip (to confirm your new settings)
[Device name]>
show tftp (to confirm your new settings)
[Device name]>
reboot 0
Example:
[Device name]>
set ipaddrtype static
[Device name]> set ipaddr 10.0.0.12
[Device name]> set ipsubmask 255.255.255.0
[Device name]>
set tftpipaddr 10.0.0.20
[Device name]>
set tftpfilename MyImage.bin
[Device name]>
set ipgw 10.0.0.30
[Device name]>
show ip
[Device name]>
show tftp
[Device name]>
reboot 0
Result: The AP will reboot and then download the image file. You should see downloading activity begin after a few seconds within the
TFTP server’s status screen.
8. When the download process is complete, configure the AP as described in Getting Started and Performing Advanced Configuration.
Setting IP Address using Serial Port
Use the following procedure to set an IP address over the serial port using the CLI. The network administrator typically provides the AP IP
address.
Hardware and Software Requirements
• Standard straight-through serial data (RS-232) cable with a one male DB-9 connector and one female DB-9 connector. The AP comes
with a female 9-pin serial port.
• ASCII Terminal software, such as HyperTerminal.
Attaching the Serial Port Cable
1. Connect one end of the serial cable to the AP and the other end to a serial port on your computer.
2. Power on the computer and AP, if necessary.
Initializing the IP Address using CLI
After installing the serial port cable, you may use the CLI to communicate with the AP. CLI supports most generic terminal emulation
programs, such as HyperTerminal (which is included with the Windows operating systems). In addition, many web sites offer shareware or
commercial terminal programs you can download. Once the IP address has been assigned, you can use the HTTP interface or the CLI over
Telnet to complete configuration.
- ORiNOCO AP-700 Access Point 1
- Copyright 2
- Trademarks 2
- OpenSSL License Note 2
- Contents 3
- Introduction 13
- Guidelines for Roaming 14
- IEEE 802.11 Specifications 15
- SNMP Management 16
- SSH (Secure Shell) Management 16
- Getting Started 17
- Active Ethernet 18
- LED Indicators 18
- Prerequisites 19
- Product Package 20
- System Requirements 20
- Hardware Installation 21
- Installing the Security Cover 22
- Mounting the AP-700 22
- Bottom Plate 23
- Screw Cavit 23
- T-Bar Ceiling Installation 24
- Installing the AP in a Plenum 25
- Initialization 26
- Setup Wizard 28
- Latest Software Availability 30
- Setup your TFTP Server 31
- Related Topics 33
- Viewing Status Information 34
- AP-700 User Guide 35
- Dynamic DNS Support 37
- IP Configuration 39
- DHCP Server 40
- DHCP Relay Agent 41
- DHCP Server IP Address Table 42
- Link Integrity 43
- Operational Mode 45
- TX Power Control 46
- Wireless (802.11a/b/g Radio) 47
- RTS/CTS Medium Reservation 48
- Wireless Service Status 49
- Multicast Rate 49
- Coverage 50
- Ethernet 53
- Management 54
- Services 55
- Telnet Configuration Settings 57
- Secure Shell (SSH) Settings 57
- Serial Configuration Settings 58
- Filtering 65
- Static MAC Filter Examples 66
- Advanced 68
- TCP/UDP Port 68
- Severity Levels 69
- • Operational Trap Group 70
- • Flash Memory Trap Group 70
- • TFTP Trap Group 70
- Alarm Host Table 71
- Syslog Messages 73
- Rogue Scan 74
- Rogue Scan Data Collection 75
- Spanning Tree 77
- Storm Threshold 77
- Intra BSS 77
- Packet Forwarding 78
- Priority Mapping 81
- Radius Profiles 85
- Configuring Radius Profiles 86
- RADIUS Accounting 88
- Accounting Attributes 89
- Security Profile 93
- VLANs and Security Profiles 95
- Configuring Security Profiles 95
- MAC Access 98
- Wireless 98
- SSID/VLAN/Security 100
- Monitoring the AP-700 104
- IP/ARP Table 106
- Learn Table 107
- Interfaces 109
- Station Statistics 110
- Performing Commands 112
- HTTP File Transfer Guidelines 113
- TFTP File Transfer Guidelines 113
- Update AP 114
- Update AP via HTTP 115
- Retrieve File 117
- Help Link 121
- Troubleshooting the AP-700 122
- Symptoms and Solutions 123
- Client Connection Problems 124
- VLAN Operation Issues 125
- Recovery Procedures 126
- Forced Reload Procedure 127
- Download Procedure 128
- RADIUS Authentication Server 130
- TFTP Server 131
- General Notes 132
- Navigation and Special Keys 133
- CLI Error Messages 133
- Bootloader CLI 133
- CLI Command Types 135
- Parameter Control Commands 139
- Working with Tables 142
- Using Strings 142
- Log into the AP using Telnet 143
- Change Passwords 144
- [Device-Name]>show wif 145
- Set up Auto Configuration 147
- Other Network Settings 148
- Configure DHCP Relay 149
- Configure DHCP Relay Servers 149
- (Mbits/sec)> 150
- Configure Syslog 152
- Configure Intra BSS 152
- Configure MAC Access Control 152
- Set RADIUS Parameters 153
- Set Rogue Scan Parameters 155
- CLI Monitoring Parameters 156
- Parameter Tables 157
- System Parameters 158
- Network Parameters 159
- DHCP Server Parameters 160
- DHCP Relay Group 160
- DHCP Relay Server Table 161
- Link Integrity Parameters 161
- Interface Parameters 162
- 802.11a Only Parameters 163
- 802.11b Only Parameters 164
- 802.11b/g Only Parameters 165
- Management Parameters 167
- Telnet Parameters 168
- Serial Port Parameters 168
- SSH Parameters 168
- Auto Configuration Parameters 170
- TFTP Server Parameters 170
- IP Access Table Parameters 170
- Filtering Parameters 171
- Proxy ARP Parameters 172
- IP ARP Filtering Parameters 172
- Broadcast Filtering Table 172
- TCP/UDP Port Filtering 172
- Alarms Parameters 173
- Bridge Parameters 174
- RADIUS Parameters 176
- Security Parameters 178
- VLAN/SSID Parameters 178
- Security Profile Table 179
- Other Parameters 181
- CLI Batch File 184
- CLI Batch File Error Log 185
- ASCII Character Chart 186
- Specifications 187
- Advanced Bridging Functions 188
- Security Functions 188
- Hardware Specifications 189
- Radio Specifications 190
- 802.11b Channel Frequencies 191
- 802.11g Channel Frequencies 191
- Wireless Communication Range 192
- 802.11g 193
- Technical Support 194
- Statement of Warranty 195
- Other Information 196
- Regulatory Information 197
- Information to the User 198
- Wireless LAN and Your Health 199
- CONSERVEZ CES INSTRUCTIONS 200
- Informazioni per l’utente 202
- Wireless LAN e la salute 203
- Informazioni legali 203
- WICHTIGE SICHERHEITSHINWEISE 204
- Rechtliche Hinweise 205
- Información para el usuario 206
- LAN inalámbrica y su salud 207
- Información sobre normativas 207
- 重要な安全上の指示事項 208
- Base Station 製品に関する追加設置要件 208
- これらの指示書を保管してください 208
- 無線 LAN と人体への影響 209
- 規制に関する情報 209
- United States FCC Information 210
- Canada IC Information 211
- Europe Information 212
- Japan Information 214
- South Korea Information 215
- Certifications radio 216
- Omologazioni radio 216
- Funkgenehmigungen 216
- Permisos de utilización 216
- Radio Approvals 217
Relacionado con productos y manuales para Hardware Proxim ORiNOCO AP-700
Hardware Proxim ORINOCO AP-2000 Manual de usuario
(244 paginas)
(244 paginas)
Hardware Proxim Stratum Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales