Proxim ORiNOCO Guía de usuario Pagina 40
- Pagina / 145
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Access Point Features AP-800 User Guide
Configuring the Device
40
RADIUS Accounting
Using an external RADIUS server, the AP can track and record the length of client sessions on the access point by
sending the RADIUS accounting messages per RFC2866. When a wireless client is successfully authenticated, RADIUS
accounting is initiated by sending an “Accounting Start” request to the RADIUS server. When the wireless client session
ends, an “Accounting Stop” request is sent to the RADIUS server.
NOTE: Each VLAN can be configured to use a separate RADIUS accounting server (and backup accounting server).
Session Length
Accounting sessions continue when a client reauthenticates to the same AP. Sessions are terminated when:
1. A client disassociates
2. Session-Timeout attributes are configured in the Radius server.
If the client roams from one AP to another, one session is terminated and a new session begins.
NOTE: This feature requires RADIUS authentication using 802.1x. If the clients are using Local MAC Authentication or
RADIUS MAC Authentication, then the session length is not tracked.
Authentication Attributes
• User-Name
This Attribute indicates the name of the user that needs to be authenticated. It must be sent in Access-Request packets if
available.
• User-Password
This Attribute indicates the password of the user to be authenticated, or the user's input following an Access-Challenge.
It is only used in Access-Request packets.
• NAS-IP-Address
This Attribute indicates the identifying IP Address of the NAS which is requesting authentication of the user, and should
be unique to the NAS within the scope of the RADIUS server. NAS-IP-Address is only used in Access-Request packets.
•State
This Attribute is available to be sent by the server to the client in an Access-Challenge and must be sent unmodified from
the client to the server in the new Access-Request reply to that challenge, if any.
• Class
This Attribute is available to be sent by the server to the client in an Access-Accept and should be sent unmodified by the
client to the accounting server as part of the Accounting-Request packet if accounting is supported.
• Session-Timeout
This Attribute sets the maximum number of seconds of service to be provided to the user before termination of the
session or prompt. This Attribute is available to be sent by the server to the client in an Access-Accept or
Access-Challenge.
• Termination-Action
This Attribute indicates what action the NAS should take when the specified service is completed. It is only used in
Access-Accept packets.
• Called-Station-Id
This Attribute allows the NAS to send in the Access-Request packet the phone number that the user called, using Dialed
Number Identification (DNIS) or similar technology. It isonly used in Access- Request packets.
• Calling-Station-Id
- ORiNOCO AP-800 1
- Copyright 2
- Trademarks 2
- GPL License Note 2
- OpenSSL License Note 2
- AP-800 User Guide 7
- Introduction 8
- Core Features of AP-800 9
- Hardware Overview 10
- Prerequisites 12
- System Requirements 13
- Product Package 13
- Optional Accessories 14
- Hardware Installation 14
- Using a Console Port 15
- Install the Antenna 15
- Mount the Unit 15
- Power on the Unit 16
- Initialization 17
- Installing the Software 20
- Update Device 21
- Retrieve From Device 23
- Managing the Access Point 27
- SNMP Management 28
- SSH (Secure Shell) Management 28
- HyperTerminal 28
- ProximVision ES 29
- Password Management 31
- Access Point Features 34
- Ethernet 36
- Security 36
- IP Configuration 43
- TPID Priority CFI VID 45
- Managing the Device 48
- Upgrading the Firmware 49
- Monitoring the Device 51
- Interface Statistics 52
- Network Layer 54
- Web Interface Overview 56
- Error Message 56
- Configuring the Device 57
- Filtering 72
- Management Access Control 86
- System Log 88
- Event Log 90
- Pre-requisites 99
- Viewing the MIB Objects 99
- Configuring the MIB Objects 100
- Global Configuration Mode 101
- General Notes 101
- Log into the AP using Telnet 104
- User Exec Mode 104
- Privileged Exec Mode 105
- Show QoS EDCA Command 109
- Wireless VAP Command 110
- System Information Command 115
- Event Logand ICMP Commands 116
- RADIUS Client Access Command 118
- Interface Statistics Command 118
- Filter-status 119
- Protocol-name 119
- Protocol-number 119
- Again entry-status 119
- Troubleshooting 121
- Symptoms and Solutions 122
- Client Connection Problems 124
- VLAN Operation Issues 124
- Gigabit Ethernet PoE 125
- Recovery Procedures 126
- Related Applications 130
- ASCII Character Chart 131
- Bootloader CLI 132
- Specifications 134
- Advanced Bridging Functions 135
- Security Features 135
- Hardware Specifications 136
- Available Channels 137
- Support Options 142
- Statement of Warranty 144
- Other Information 145
Relacionado con productos y manuales para Redes Proxim ORiNOCO
Redes Proxim ORiNOCO Guía de instalación
(35 paginas)
(35 paginas)
Redes Proxim ORiNOCO AP-8000 Guía de usuario
(169 paginas)
(169 paginas)
Redes Proxim RangeLAN2 7921 Guía de usuario
(103 paginas)
(103 paginas)
Redes Proxim ORiNOCO AP-2500 Guía de usuario
(251 paginas)
(251 paginas)
Redes Proxim AP-2000 Guía de usuario
(244 paginas)
(244 paginas)
Redes Proxim RangeLAN2 7500 Manual de usuario
(141 paginas)
(141 paginas)
Redes Proxim 7910 Guía de usuario
(127 paginas)
(127 paginas)
Redes Proxim RangeLAN2 7921 Especificaciones
(76 paginas)
(76 paginas)
Redes Proxim RANGELAN2 7510 Guía de usuario
(84 paginas)
(84 paginas)
(9 paginas)Pilot-usa MG-ANR podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Akcesoria komunikacja Pilot-usa MG-ANR.
Dostarczamy 1 pdf podręczników Pilot-usa MG-ANR do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comentarios a estos manuales