Proxim RangeLAN2 7921 Manual de instrucciones Pagina 49
- Pagina / 333
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Transferring Files 2-17
2325A137REFGD Revision B 2325 Reference Guide
An Example
To transfer a file named MYFILE from a PC to a 2325 using Xmodem
protocol, you could use the following lines.
On the PC: xfer myfile. This command causes the computer to
send the specified file using XFER’s default settings.
On the 2325: xfer /r myfile. This command causes the 2325 to
receive the specified file transmitted from the PC.
Note: For more information about XFER, including Zmodem options,
see Chapter 5 “Using XFER.”
- Reference Guide 1
- Revision Notice 3
- 2325 Reference Guide 3
- Table of Contents iii 7
- Table of Contents v 9
- Table of Contents 13
- Chapter 1 15
- Document Conventions 16
- Technical Specifications 17
- Keyboard 18
- Display 18
- Battery 19
- Power Management 20
- Laser Module 21
- Radio PC Card 22
- PC Card 23
- Serial/Accessory 24
- Contacting LXE 25
- LXE Repair Services 26
- 125 Technology Parkway 26
- Norcross, GA 30092 26
- Manuals and Accessories 27
- Chapter 2 33
- Using Advanced Features 33
- Resetting the 2325 35
- Safe Boot 36
- Hardware Reset 37
- Using PC Cards 38
- Inserting a PC Card 39
- Radio Card Antenna Connector 41
- Radio Card Antenna Ports 41
- Removing a PC Card 42
- The Serial Port 43
- The Scanner Port 43
- The Antenna 44
- The Disk Drives 45
- Configuring the 2325 46
- Transferring Files 47
- Advanced Power Management 50
- Radio PC Card Configuration 52
- ODI with TCP/IP 53
- ODI with NetWare 55
- ODI With IPX/SPX 57
- Installing NDIS Drivers 59
- Link Support Layer 62
- TCPIP Protocol 62
- Install Proxim 62
- RangeLAN2 Drivers 62
- DOS Configuration 63
- Parameters 63
- Setting the RangeLAN2 65
- Security ID 65
- Install Lucent 66
- WaveLAN II Drivers 66
- NET.CFG File and 67
- MU Access Control 70
- Message Filtering 70
- Site Survey 71
- Throughput and Performance 72
- Operational Problems 72
- Problems with DOS Drivers 74
- Chapter 3 79
- Software Configuration 79
- Disk Drives and Files 80
- Drive A 81
- Drive B 83
- Drive C 86
- PCM Directory Files 87
- Drive D 88
- Drive E 88
- System Configurations 89
- Data Entry 92
- Terminal Emulation 93
- DOS Terminal 94
- Emulation User 94
- Defined Stored Forms 94
- 4-ii Table of Contents 96
- Chapter 4 99
- The Configuration Utility 99
- BIOS Upgrade File Location 100
- RF Files Location 100
- Quick Start 103
- The Main Menu 105
- Default 107
- Configuration File 108
- Settings File 109
- Configuration 111
- Settings 112
- First File 113
- Configuration Window 113
- Main Application 114
- Application Files 114
- Second File 117
- ATA Memory Cards 117
- I/O Cards 117
- Vendor Specific 118
- DOS Files 118
- Third File 121
- Text File 122
- The Program Settings Windows 123
- First Program 125
- Settings Window 125
- (Default.PRS) 125
- Second Program 126
- Third Program 127
- Fourth Program 128
- Fifth Program 129
- Last Program Settings 130
- Window (Default.PRS) 130
- The Comm Settings Dialog Box 131
- The File Transfer Window 132
- Files to Transfer 134
- Receive 136
- XFER 5-1 139
- Chapter 5 141
- Using XFER 141
- Introduction 141
- About XFER 141
- Syntax and Parameters 142
- Mcommand 151
- Multiple-Option Blocks 162
- Keywords 164
- DIAL_METHOD 165
- FAIL_STRINGS 165
- HANDSHAKING 165
- INIT_STRING 166
- LOCKED_BAUDRATE 166
- NUMBER# 166
- PROTOCOL_STRINGS 167
- Performance 169
- Error Codes 170
- Chapter 6 173
- Commands 173
- System Utilities 173
- CFGDEV.SYS 174
- CFGIO.EXE 175
- COMIO.COM 176
- DECODE.SYS 176
- FLASHDSK.SYS 177
- FORMAT.COM 177
- LOCK.COM 178
- ORGANIZE.COM 179
- VDISK.SYS 180
- XFER.EXE 180
- ROM-DOS Commands 181
- ATTRIB.EXE 183
- BUFFERS 184
- CHKDSK.EXE 185
- COMMAND.COM 187
- FIND.EXE 192
- HELP.COM 194
- NEWFILE 194
- PRINT.EXE 196
- SHARE.EXE 197
- SWITCHES 199
- TREE.COM 200
- XCOPY.EXE 202
- Illustrations 206
- Chapter 7 207
- The Docking Stations 207
- The Single Dock 208
- The Power Adapter 209
- Using a Single Dock 210
- Power Supply 211
- The Four Slot Dock 212
- Back Panel 213
- Creating a Dock Network 214
- Installation 215
- Using the 4-Slot Dock 216
- Operating Modes 216
- The 4SLOT.SYS Device Driver 217
- Transferring Files with XFER 218
- Setting the Baud Rate 219
- Using the DC Single Dock 222
- Before Installation 223
- Begins . . 223
- Vehicle 12VDC 224
- Connection 224
- Fuse Replacement 225
- LXE Vehicle Bracket 225
- Custom Mounting 228
- Brackets 228
- Vehicle Mount Dock 230
- Mounting to a Vehicle 231
- Using the Vehicle Mount Dock 231
- Appendix A 235
- Connector Configurations 235
- The 2325 Computer 236
- Serial Port Jack 237
- Single Dock 238
- 25-Pin Connector 239
- The 4-Slot Dock 241
- Host-Interface Cable 242
- Dock-Network Cable Jacks 243
- Appendix B 247
- Programming Parameters 247
- Code 39 248
- Interleaved 2 of 5 249
- Matrix 2 of 5 249
- Standard 2 of 5 250
- Code 11 250
- Codabar/Ames 251
- Code 93 252
- Numbering (JAN) 253
- UPC, EAN, JAN Extensions 254
- Code 128 254
- Labelcode 4/5 254
- Other Controls 255
- 2325 C-1 259
- C-ii Table of Contents 260
- Table of Contents C-iii 261
- C-iv Table of Contents 262
- Appendix C 263
- Barcodes for Configuring 2325 263
- Default Settings 264
- Barcodes 267
- Maximum Length 268
- Enable Checksum 269
- Send Checksum 270
- Full ASCII Mode - On 270
- Use Lengths 6 and 274
- 14 Only (Case Code) 274
- *$+$-141EE* 278
- *$+$-140EE* 278
- Use 2-Bar Start/Stop 282
- Enable - Off 283
- Minimum Length - 4 283
- Require 2 Check 285
- Digits - Off 285
- *$+$-1F1EE* 286
- *$+$-1F0EE* 286
- Send Stop/Start - Off 290
- Codabar-to-CLSI 291
- Conversion - Off 291
- Wide Intercharacter 291
- Gaps Allowed - On 291
- Check Digit Mod 295
- 11 - Off 295
- Send Check Digit(s) 295
- Minimum Length - 2 296
- C-36 Barcodes 298
- Enable UCC/EAN 128 301
- Enable UPC-A - On 303
- Send System Digit 303
- Send Check Digit 304
- Convert UPC-A to 304
- EAN-13 - Off 304
- Use System Digit 0 305
- Use System Digit 1 305
- Convert UPC-E to 306
- UPC-A - Off 306
- *$+$-381EE* 307
- UPC-E Send Check Digit On 307
- *$+$-380EE* 307
- UPC-E Send Check Digit Off 307
- Enable EAN-8/JAN-8 308
- Enable EAN-13/JAN 308
- Convert EAN-13 to 309
- ISBN - Off 309
- Send EAN/JAN 309
- Checksum - Off 309
- UPC/EAN/JAN Extensions 310
- *$+$-3E1EE* 311
- *$+$-3E0EE* 311
- Auto-Off Timer - 5 313
- Send Symbology 314
- Identifier - Off 314
- Good-Read Beep 315
- Tone (in Hertz) 315
- Number of Good 316
- Read Beeps - 1 316
- Duration (in 317
- Beeper Volume 318
- Error Beep Tone (in 319
- Hertz) - 2580 319
- *$+$-D41EE* 320
- Long Range Trigger Mode On 320
- *$+$-D40EE* 320
- Long Range Trigger Mode Off 320
- Spot Beam Timeout 321
- (in seconds) 0.5 321
- Release Scan 322
- Timeout (in seconds) 322
- Spotting Beam 323
- Enable - On 323
- Keypress Sound 323
- Enable Ctl-Alt-Del 324
- Reboot - On 324
- Enable Trigger 324
- Programmability 324
- Backlight Auto-Off 325
- *$+$-E220EE* 326
- *$+$-E230EE* 326
- Regulatory Notices 328
- An EMS Technologies Company 330
© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales