Proxim Network Router CPN 63708 Manual de usuario

Installation and Management TSUNAMI MP.11 CPN 63708Issue Date: 02/05/2003

Tsunami MP.11 Installation and Management 3. Unlock the unit’s cable cover. To release the cable cover, press down on the cable cover lock located i

Tsunami MP.11 Installation and Management 6. Connect one end of an Ethernet cable to the Ethernet port. The other end of the cable should not be con

Tsunami MP.11 Installation and Management The Kensington Security Slot is shown in the following figures (the figure on the left shows the slot with t

Tsunami MP.11 Installation and Management INSTALLING DOCUMENTATION AND SOFTWARE The MP.11 also comes with documentation and software on a CD-ROM. To i

Tsunami MP.11 Installation and Management MOUNTING THE MP.11 The following are the mounting options for the MP.11: ▪ Desktop Mount ▪ Wall Mount ▪

Tsunami MP.11 Installation and Management 8. Place the back cover on the mounting location and mark the center of the three mounting holes. 9. Remov

Tsunami MP.11 Installation and Management Ceiling Mounting Follow these steps to mount the MP.11 to a ceiling. 1. Unplug the MP.11’s power supply, if

Tsunami MP.11 Installation and Management Chapter 3. Management Overview This chapter describes how to gain access to the MP.11 for configuration and

Tsunami MP.11 Installation and Management Static or Dynamic IP Address The MP.11 can use either a static or dynamic IP address. ▪ Static IP address

Tsunami MP.11 Installation and Management 3. Ensure that Static is selected as the IP Address Type and fill in the IP Address and Subnet Mask suitabl

Tsunami MP.11 Installation and Management Notices COPYRIGHT ©2003 Proxim Corporation, Sunnyvale, CA. All rights reserved. Covered by one or more of

Tsunami MP.11 Installation and Management WEB INTERFACE OVERVIEW The Web Interface provides a graphical user interface with which you can easily confi

Tsunami MP.11 Installation and Management COMMAND LINE INTERFACE OVERVIEW The Command Line Interface (CLI) is a text-based interface with which you ca

Tsunami MP.11 Installation and Management Serial Port You can also use the CLI through the serial port of the MP.11 with a terminal program such as Hy

Tsunami MP.11 Installation and Management HyperTerminal Connection Properties The serial connection properties can be found in HyperTerminal as follow

Tsunami MP.11 Installation and Management Chapter 4. Basic Management This chapter describes the initial setup of the MP.11, which lets you set up an

Tsunami MP.11 Installation and Management REBOOTING AND RESETTING Some configuration changes require a restart. There are several ways to restart the

Tsunami MP.11 Installation and Management Soft Reset to Factory Default If necessary, you can reset the MP.11 to the factory default settings. Resett

Tsunami MP.11 Installation and Management SYSTEM CONFIGURATION The system configuration page lets you change the MP.11’s system name, location name, a

Tsunami MP.11 Installation and Management Descriptor Shows the product name and firmware build version. Up Time How long the device has been up and r

Tsunami MP.11 Installation and Management IP Address The static IP address of the MP.11 (default IP address is 10.0.0.1). Subnet Mask The mask of the

Tsunami MP.11 Installation and Management Contents Copyright ...

Tsunami MP.11 Installation and Management The wireless interface settings differ per mode. WORP Base and WORP Satellite Mode You can change the foll

Tsunami MP.11 Installation and Management Maximum Satellites (only WORP Base) This is the maximum number of satellites that can register to a base. It

Tsunami MP.11 Installation and Management The recommended setting is auto-speed-auto-duplex. You can also limit the traffic of the Ethernet interface

Tsunami MP.11 Installation and Management Interfaces To monitor transmission details, click Monitor Î Interfaces. The Interfaces tab provides detaile

Tsunami MP.11 Installation and Management SECURITY SETTINGS To prevent misuse, the MP.11 provides wireless data encryption and password-protected acce

Tsunami MP.11 Installation and Management Related CLI commands: show wifsec set wifsec 3 encryptkey1 <key 1> set wifsec 3 encryptkeytx <1 - 4

Tsunami MP.11 Installation and Management UPGRADING THE MP.11 The MP.11 is equipped with embedded software that can be updated. Updates can be found

Tsunami MP.11 Installation and Management Chapter 5. Web Interface This section covers the Web Interface of the MP.11. The interface is described hie

Tsunami MP.11 Installation and Management Systems Traps This section shows the status of system traps. System traps occur when the MP.11 encounters i

Tsunami MP.11 Installation and Management 2) Network IP Configuration Click Configure Î Network Î IP Configuration to view and configure local IP add

Tsunami MP.11 Installation and Management Chapter 1. Overview The Tsunami MP.11 is a flexible wireless Outdoor Router that lets you des

Tsunami MP.11 Installation and Management Click Configure Î Network Î DHCP R A to enable the MP.11 DHCP relay agent. When enabled, the DHCP relay ag

Tsunami MP.11 Installation and Management 3) Interfaces Wireless Slot A Click Configure Î Interfaces Î Wireless Slot A to change the wireless interfac

Tsunami MP.11 Installation and Management The Base Station must not be configured at a higher data rate as any of the SUs, as the timeout of the Base

Tsunami MP.11 Installation and Management Trap Groups The user can enable or disable different types of traps in the system. By default, all traps ar

Tsunami MP.11 Installation and Management 6) Serial Click Configure Î Serial to change the serial port settings. 7) HTTP Click Configure Î HTTP to vi

Tsunami MP.11 Installation and Management 8) Security MAC Authentication Click Configure Î Security Î MAC Auth to build a list of authorized wireless

Tsunami MP.11 Installation and Management In large networks with multiple MP.11 devices, you can maintain a list of MAC addresses on a centralized loc

Tsunami MP.11 Installation and Management Ethernet Protocol Filter The Ethernet Protocol Filter blocks or forwards packets based upon the Ethernet pr

Tsunami MP.11 Installation and Management Filter Operation Type Passthru: Only the enabled Ethernet Protocols listed in the Filter Table pass through

Tsunami MP.11 Installation and Management Wireless Mask Enter the appropriate bit mask to specify the range of MAC addresses to which this filter is t

Tsunami MP.11 Installation and Management WIRELESS NETWORK TOPOLOGIES You can use the MP.11 to set up the following types of topologies: ▪ Point-to

Tsunami MP.11 Installation and Management For more information about Spanning Tree protocol, see Section 8.0 of the IEEE 802.1d standard. The Spannin

Tsunami MP.11 Installation and Management Broadcast Protocol Filtering Click Configure Î Filtering Î Broadcast Protocol Filtering to deny specific IP

Tsunami MP.11 Installation and Management WORP Click Monitor Æ WORP to monitor the performance of the WORP Base or WORP Satellite interfaces. Chapte

Tsunami MP.11 Installation and Management 2) ICMP Click Monitor Æ ICMP to view the number of ICMP messages send and received by the MP.11. It include

Tsunami MP.11 Installation and Management 4) Per Station Click Monitor Æ Per Station to view the following information: 5) Features Click Monitor Æ F

Tsunami MP.11 Installation and Management 7) Interfaces Click Monitor Æ Interfaces to view detailed information about the IP-layer performance of the

Tsunami MP.11 Installation and Management 9) Learn Table Click Monitor Æ Learn Table to view all MAC addresses the MP.11 has detected on an interface.

Tsunami MP.11 Installation and Management COMMANDS This section describes the commands that you can perform with the Web Interface. There are five ta

Tsunami MP.11 Installation and Management 2) Upload Click Commands Æ Upload to upload a configuration file from the MP.11. 3) Reboot Click Commands Æ

Tsunami MP.11 Installation and Management 4) Reset Click Commands Æ Reset to restore the configuration of the MP.11 to the factory default values. You

Tsunami MP.11 Installation and Management Point-to-Multipoint Network If you want to connect more than two buildings, you can set up a single Point-to

Tsunami MP.11 Installation and Management Chapter 6. Command Line Interface INTRODUCTION The Command Line Interface (CLI) provides a text-based inter

Tsunami MP.11 Installation and Management VIEWING AND CHANGING PARAMETERS You can view and change MP.11 parameters with the SHOW and SET commands, res

Tsunami MP.11 Installation and Management WORKING WITH TABLES In some cases, parameters are stored in tables whose rows contain similar parameters. C

Tsunami MP.11 Installation and Management Modifying Several Table Entries You can also modify several table entries at once by indicating the index of

Tsunami MP.11 Installation and Management Chapter 7. Procedures This chapter contains a set of procedures, as described in the following table: Proce

Tsunami MP.11 Installation and Management IMAGE FILE DOWNLOAD In some cases, it may be necessary to upgrade the embedded software of the MP.11 by down

Tsunami MP.11 Installation and Management CONFIGURATION BACKUP You can back up the MP.11 configuration by uploading the configuration file. You can

Tsunami MP.11 Installation and Management CONFIGURATION RESTORE You can restore the configuration of the MP.11 by downloading a configuration file. T

Tsunami MP.11 Installation and Management SOFT RESET TO FACTORY DEFAULT If necessary, you can reset the MP.11 to the factory default settings. Resetti

Tsunami MP.11 Installation and Management FORCED RELOAD With Forced Reload, you reset the MP.11 to the factory default settings and erase the embedded

Tsunami MP.11 Installation and Management Chapter 2. Installation This chapter describes the steps required to install the MP.11 installation steps,

Tsunami MP.11 Installation and Management 5. Click OK to start the file transfer. The MP.11 downloads the image file. The TFTP server program should s

Tsunami MP.11 Installation and Management For example: set ipaddr 10.0.0.12 set ipsubmask 255.255.255.0 set ipaddrtype static set tftpipaddr 10.0.0.20

Tsunami MP.11 Installation and Management Chapter 8. Specifications This chapter provides Hardware and Radio Specifications. HARDWARE SPECIFICATIONS

Tsunami MP.11 Installation and Management RADIO SPECIFICATIONS Channel Frequencies The following table shows the channel allocations that vary from co

Tsunami MP.11 Installation and Management Chapter 9. Troubleshooting This chapter helps you to isolate and solve= problems with your MP.11. In the ev

Tsunami MP.11 Installation and Management Power Ethernet Link Wireless Link OFF when no power is present or malfunctioning Green when power is p

Tsunami MP.11 Installation and Management 5. Press the RESET button on the MP.11 unit. The terminal program displays Power On Self Tests (POST) mess

Tsunami MP.11 Installation and Management Setup and Configuration Ethernet Link does not work First check the Ethernet LED; ▪ Dim is “no media conne

Tsunami MP.11 Installation and Management SETUP AND CONFIGURATION The following issues relate to setup and configuration problems. Lost the MP.11 Pass

Tsunami MP.11 Installation and Management Command Line Interface Does Not Work If you cannot connect to the MP.11 through the network: 1. Connect a c

Tsunami MP.11 Installation and Management ▪ The unit must not be covered and the air must be able to flow freely around the unit. ▪ The unit must be

Tsunami MP.11 Installation and Management Changes Do Not Take Effect Changes made in the Web Interface do not take effect: 1. Restart your Web browse

Tsunami MP.11 Installation and Management Glossary ARP DHCP Relay Agent The Address Resolution Protocol (ARP) is intended to find the MAC address belo

Tsunami MP.11 Installation and Management Parameter HTTP Hypertext Transfer Protocol (HTTP) is the protocol to transport Web pages. When you access th

Tsunami MP.11 Installation and Management Glossary 83 CPN 63708 Issue Date: 02/05/2003 Simple Network Management Protocol (SNMP) A protocol used

Tsunami MP.11 Installation and Management º TFTP Server (which lets you transfer files across the network). You can download configuration and licen